22 as a nice little farm rifle. Upon activating the lever, the breech block pivots, or swings down to expose the chamber.Lately I have been using an old stevens. This type of rifle action is known as a pivoting block type, or swinging block, since the breech block is pivoted on a pivot screw in the mid section of the receiver. And closely associated versions.
Top Rated Seller Top Rated Seller. 22 Rifle vintage AD Hunting WWII. Upon activating the lever, the breech block pivots, or swings down to expose the chamber.1945 STEVENS Shotguns &. The problem is (that you will see in the.This type of rifle action is known as a pivoting block type, or swinging block, since the breech block is pivoted on a pivot screw in the mid section of the receiver.
This article is not meant to be the BIBLE, in that many times if something is printed, there may later be some gun show up to prove us wrong. 22 Long Rifle round and made a number of rifle, shotgun, and target pistol designs before being bought by Savage Arms in 1920.These firearms evolved basically with many internal running changes happening over the time span that the guns were in production. Buy It NowThe company introduced the. Top Rated Seller Top Rated Seller. 1902 Stevens Favorite Rifles Vintage Print Ad 17720. S N p O Y o P n V s o r F e 8 d Z 7 D.
Some manufacturers would assign higher numbers at the start of a model to fool the competition into thinking they were making a lot of guns. Now this is not to say that these letters were in alphabetical order either. When that upper number was reached for that letter, they picked another letter & started over.
These wood screws are 1.050″ in length with a body dia. This model designation was never stamped on the gun however & was only mentioned in the sales catalog.Standard sights on the 1889 & 1894 were fixed with the rear being just a triangular metal section & not adjustable for elevation.All versions utilized a wood screw on each of the top & bottom of each tang to secure the buttstock in place. The barrel & or sights were what determined the different models. The later guns bore different model designation, as say (17, 20, 27). The early guns that had a part octagon barrel only had it on the top of the barrel, stopping at the front of the forearm, while the barrel under the forearm wood was round. However they could have been had in round, round/part octagon, or octagon in different lengths.
The lower part of the frame under the barrel extends forward enough in front of barrel shank abutment to accommodate the barrel takedown screw. The following are my observations.The sideplate is on the RH side of receiver, held on by 5 screws, 3 of which are the trigger, hammer & finger lever pivot screws. However recently a customer sent an action in for us to examine. Since there are so few of them out there, I had about given up hope of ever seeing one. 1889 Sideplate version–In Frank de Haas’s book, Single Shot Rifles & Actions in chapter 17, he covers a 1889 Sideplate version. 270 dia.Buttplates appear to have been made of black hard rubber.
Apparently it is screwed into the inside LH side of the receiver & activated by the breechbolt’s link pin that is slightly extendedThe sideplate style would make sense from the manufacturing standpoint, in that when getting a new model into production, it would have been easier to make it this way to get a prototype up & going faster.The mainspring for this version is a thin lazy “S” shaped spring that the rear just snaps in front of a abutment lug on the lower tang. The extractor hook is at a 35 degree angle. It has a recessed screw head that acts as a pivot point.
Old Stevens 22 Rifles Install The 1894
You can tell if the screw is just an abutment type screw if when the screw is tightened all the way in against the lower tang with no mainspring under it, the radiused threaded end will be just even with the bottom of the tang.If you install the 1894 mainspring on this version, the hammer will not cock as the hammer is totally different. On the later type, many times the rear of the mainspring may have a slight convex radius where it abuts the abutment screw to keep it from sliding off sideways.Stevens Favorite 1889 Hammer & Mainspring, drawn to sizeThe version which used the screw as a stud could be later versions, as it appears that the 1894’s utilized this same hole & spacing for attaching it’s mainspring. This flat is what is needed to clear the rear of the hammer when cocked. The mainspring goes in backwards from what you may imagine, in that the flat end goes forward.
Stepped barrel shank (.630 &. The trigger & spring appears to be the same on all models.1889 & early 1984 with side style extractor — had a 2 dia. To accommodate this, the wood has to be relieved back about 1 1/2″ from where it abuts the rear of the receiver.The barrel-takedown screw had a bow loop into the head of the screw. On this version, the 1894 mainspring could possibly be used if BOTH 1894 hammer & mainspring were used.You can also help identify this type, if the buttstock is original, in that this thin mainspring is arched enough that it many times will touch the underside of the top tang.
1894 —The 1894’s were probably the most proliferate as to the many varied different type of parts improvements in relationship to barrels, extractors, breechblocks, forends & stocks. Forearm length varied with the version & the barrel configuration. This could be adjusted against the bottom of the barrel to allow take up for worn linkage that allowed the lever to droop.Forearms for both the 1889 & the early 1894’s had a slight schnabbel on the front. The center of the breechblock under the barrel’s rear had a small screw with the head bearing against the bottom of the barrel. These used the side style extractor, sometimes called the 7 o’clock style.
The next version in succession had a short threaded section on the barrel in front of the receiver & utilized a thin knurled ring that threaded onto the barrel at the juncture against the receiver front. The top side rear of the receiver at the top flat at the rear of the barrel (at the hammer area) had a more square corner on the early guns. By the time the 1915 came out the options had dwindled.Stevens Favorite 1894 Hammer & Mainspring, drawn to sizeThe early 1894’s had the same side style extractor as the 1889 guns. This was also in an era that the factories would offer special options when ordering firearms.
193 dia hole for the pivot screw. 240 wide top at the case rim, & a. Then still later the whole adjustment system was dropped.One observation is that the 1894 center style extractors had the. Later guns used a spring loaded plunger inside the lever that put tension on the link.
Old Stevens 22 Rifles Full A Extraction
Later they simply milled the left side hole of the lever out enough to accept the extractor better & them pressed a bushing in the hole to reduce it down to the screw dia. It was not possible to allow them to machine the proper recess for the bottom part of the extractor below the pivot screw hole. As the levers of the first center type extractors did not have enough metal at the contact point to stand up for extended usage, & it’s contact with the extractor would not give as full a extraction movement as designed. The breech block for this late version would have had a wider slot in the front to accept this wider (1/4″) extractor.The section of the lever that exerts pressure on the extractor on the final extraction has been changed.
0 kommentar(er)
